Foro de Armas.es

Hola amigos,pues eso,haber si alguien sabe decirme como puedo averiguar la edad de un S&w 686?,gracias de antemano y un saludo al foro

Aqui tienes un foro donde preguntar.
https://smith-wessonforum.com/forum.php
Solo tienes que inscribirte.
Es ingles a ser posible.
Saludos.

Buenas!

Una primera aproximación es saber que modelo concreto es: 686-x, donde la x es un número. Eso te da un año de arranque.

El resto no es facil. Si pones el número de serie (substituye los tres últimos por x para preservar algo la privacidad) te lo puedo mirar.

Saludos

http://books.google.es/books?id=D8qXdU45SCUC&printsec=frontcover&dq=Standard+Catalog+of+Smith+%26+Wesson&hl=en&ei=I2IoToSxOpSosAPlmP2LCQ&sa=X&oi=book_result&ct=result&redir_esc=y#v=onepage&q&f=false

Empieza en la página 19

Y aquí algo menos

http://smith-wessonforum.com/s-w-revolvers-1980-present/222977-new-members-looking-date-manufacture-info-how-find-your-serial-number-2.html

Y si quieres pagar, S&W te hace un certificado de la historia y produccion de tu modelo:

https://www.smith-wesson.com/webapp/wcs/ ... 7812_image

Al abrir el tambor veras escrito 686 con un guion y un numero. eso te dice a que serie pertenece:

686 ''dash nothing'' - 1980
686-1, 1986 - radius stud package and floating hand
686-M - 1987 recall stamping on earlier versions
686-2, 1987, hammer nose change, bushing and ***'d parts
686-3, 1988, new yoke retention system
1990 - 2 1/2" barrel introduced.
686-4 ........ 1994 thru 1998 - many changes including move to 7 shot, sight changes etc.
686-4 (1993): drilled & tapped frame, new rear sight leaf, changed extractor, start shipping w/ Hogue grips
1995: power port barrel introduced
1995: 7-shot cylinder
1996: round-butt frames only
1997: MIM thumb-piece
686-5 (1997): integral frame lug, MIM hammer, MIM trigger, frame-mounted firing-pin
686-5 had the move to MIM parts and frame mounted firing pin

-6 is when S&W started putting the lock on the 686; -5 and earlier are all pre-lock, and -4 and earlier are all pre-MIM hammer/trigger (-4s had a MIM thumbpiece).

686-7 was the Performance Center version of the 686. Same as the 686-6 -- Metal Injection Molded/MIM parts (hammer, trigger, thumbpiece, trigger rebound slide, etc.), internal lock system/ILS, round-butt grip frame, factory drilled & tapped/D&T top-strap -- but chambered for .38 Super.

686-8 is a CO2-powered pellet revolver, chambered for .177 pellets. I believe this airgun is not actually produced by S&W, but rather produced by Umarex (and S&W puts their name on it, or Umarex paid for the rights to put S&W's name on it).

If your "686-8" is a real firearm chambered for .357 Magnum, then it might actually be a 686-6, and the -6 might be either mis-stamped (it happens) or hard to make out.

Buenas!

Y yo que pagué 39.99 USD más portes por el mio...

Saludos