Penetraciones (FOTOS)
Publicado: 12 Jul 2009 21:30
He podido leer en un foro americano una relación de diferentes penetraciones - según caibres - en diferentes superficies.
Os lo pongo por si es de interés.
Un saudo!
Bare gel
.22 40g RNL 11.5
.25 ACP 50g FMJ 17.5
.32 ACP 71g FMJ 19
.38 158g RNL 23.5
.380 ACP 95g FMJ 17
.45 230 FMJ 30.5
9mm 115g FMJ RN 24.5
9mm 147g FMJ FP 28.7
9mm 124g FMJ RN +P+ 34.5
357SIG 125g FMH FP 38.5
10mm 200g FMJ FP 29.8
BULLET PENETRATION - INCHES OF PLYWOOD (test blocks made up of half inch
boards)
9mm Parabellum Inches
123 grain FMJ 4.4"
115 grain JHP +P+ 3.0"
115 grain JHP 2.7"
115 grain Silvertip 2.5"
80 grain Glaser 2.0"
.45 ACP Inches
230 grain FMJ 2.8"
200 grain JHP 2.4"
185 grain JHP 2.4"
185 grain Silvertip 1.7"
135 grain Glaser 1.3"
BULLET PENETRATION - INTERIOR WALL TESTS
Constructed of 2 sheets of 1/2" drywall mounted to 2x4" studs
on 16" centers.
Calibre Walls Penetrated Notes
9mmP FMJ 11 No expansion
.9mmP FMJ 9 Stopped by 2x4
9mmP JHP 9 No expasnion
.45 ACP JHP 8 No expansion
.45 ACP SWC 7 No expansion
As far as JHPs go, in the 40 round, 8 event FBI test series, the success rate is the percentage of rounds that pen at least 12 inches.
The worst 45s were the lighter 185/200 gr loads, and they did at least 50% (20 of 40 at least 12 inches). The old Rem 185 JHP did 95%, as did most of the 230 JHPs.
The lighter 9s did about 35%, the heavier 9s about 82.5% The lighter 357 Mags about 35%, the heavier up to 100%.
357SIG 125 Fed about 92.5%.
The 180/40s around 90%+, the 165 HS over 90%.
Through auto glass:
Speer 124/9 +P GD 13/.55
Speer 230/45 GD 11/.65
Speer 125/357S 13/.55
Fed 147/9 HS 11/.50
Fed 230/45 HS 12.8/.61
Win 147/9 RT 10.8/.52
Win 127/9 +P+ RT 9.4/.48
Win 230/45 RT 12/.58
Rem 147/9 GSB 12.1/.55
Rem 230/45 GSB 12.5/.63
45 ACP from a 5 inch 1911 through one (1) layer of denim into gel:
230 Gold Dot 14.8/.61
185 Gold Dot 15.7/.59
230 Fed JHP 16.1/.64
9mm from G17/19 through four (4) layers of denim into gel:
124 Hydra-Shok 15.7/.61
124 Gold Dot +P 14/.59
Fed 115 JHP 13/.64
Os lo pongo por si es de interés.
Un saudo!
Bare gel
.22 40g RNL 11.5
.25 ACP 50g FMJ 17.5
.32 ACP 71g FMJ 19
.38 158g RNL 23.5
.380 ACP 95g FMJ 17
.45 230 FMJ 30.5
9mm 115g FMJ RN 24.5
9mm 147g FMJ FP 28.7
9mm 124g FMJ RN +P+ 34.5
357SIG 125g FMH FP 38.5
10mm 200g FMJ FP 29.8
BULLET PENETRATION - INCHES OF PLYWOOD (test blocks made up of half inch
boards)
9mm Parabellum Inches
123 grain FMJ 4.4"
115 grain JHP +P+ 3.0"
115 grain JHP 2.7"
115 grain Silvertip 2.5"
80 grain Glaser 2.0"
.45 ACP Inches
230 grain FMJ 2.8"
200 grain JHP 2.4"
185 grain JHP 2.4"
185 grain Silvertip 1.7"
135 grain Glaser 1.3"
BULLET PENETRATION - INTERIOR WALL TESTS
Constructed of 2 sheets of 1/2" drywall mounted to 2x4" studs
on 16" centers.
Calibre Walls Penetrated Notes
9mmP FMJ 11 No expansion
.9mmP FMJ 9 Stopped by 2x4
9mmP JHP 9 No expasnion
.45 ACP JHP 8 No expansion
.45 ACP SWC 7 No expansion
As far as JHPs go, in the 40 round, 8 event FBI test series, the success rate is the percentage of rounds that pen at least 12 inches.
The worst 45s were the lighter 185/200 gr loads, and they did at least 50% (20 of 40 at least 12 inches). The old Rem 185 JHP did 95%, as did most of the 230 JHPs.
The lighter 9s did about 35%, the heavier 9s about 82.5% The lighter 357 Mags about 35%, the heavier up to 100%.
357SIG 125 Fed about 92.5%.
The 180/40s around 90%+, the 165 HS over 90%.
Through auto glass:
Speer 124/9 +P GD 13/.55
Speer 230/45 GD 11/.65
Speer 125/357S 13/.55
Fed 147/9 HS 11/.50
Fed 230/45 HS 12.8/.61
Win 147/9 RT 10.8/.52
Win 127/9 +P+ RT 9.4/.48
Win 230/45 RT 12/.58
Rem 147/9 GSB 12.1/.55
Rem 230/45 GSB 12.5/.63
45 ACP from a 5 inch 1911 through one (1) layer of denim into gel:
230 Gold Dot 14.8/.61
185 Gold Dot 15.7/.59
230 Fed JHP 16.1/.64
9mm from G17/19 through four (4) layers of denim into gel:
124 Hydra-Shok 15.7/.61
124 Gold Dot +P 14/.59
Fed 115 JHP 13/.64
