Página 1 de 1

Como tensar el gatillo del CZ 550

Publicado: 03 Sep 2013 22:19
por JAMPANA
Hace poco he adquirido este rifle y me surge una duda , ¿Para dar menos resistencia al gatillo el tornillo que hay para estos menesteres hay que girarlo en el sentido de las agujas del reloj o al contrario ?

Re: Como tensar el gatillo del CZ 550

Publicado: 03 Sep 2013 22:23
por Kempka
Prueba.

Re: Como tensar el gatillo del CZ 550

Publicado: 03 Sep 2013 22:28
por JAMPANA
Ya he probado , y creo que es en el sentido de las agujas del reloj , pero como no tengo dinamometro para probarlo quiero asegurarme con alguien que lo sepa cierto , gracias

Re: Como tensar el gatillo del CZ 550

Publicado: 03 Sep 2013 22:38
por Kempka
Llevalo a lo extremos y entonces tendras que notar la diferencia por narices.
De todas formas no necesitas pesagatillos para saber cuando esta a tu gusto.

Pregunta: ¿Solo lleva tornillo regulable para el peso?. ¿no lleva 4 (peso normal, peso del pelo, desenganche y sobrerecorrido)?.
¿No es como este?:
Imagen

Re: Como tensar el gatillo del CZ 550

Publicado: 03 Sep 2013 22:48
por JAMPANA
Caramba Kempa , eres un experto , solo he actuado sobre el "D" y efectivamente he pensado llevarlo hasta los extremos ,en cualquier caso creo que ya lo he dejado " a mi gusto" y fectivamente no hace falta mas aparatos , pero bueno si alguien lo sabe con seguridad me seria muy útil

Re: Como tensar el gatillo del CZ 550

Publicado: 03 Sep 2013 23:01
por Kempka
Esto es lo que he encontrado:
http://cz-usa.blogspot.com.es/2011/11/cz-single-set-trigger-system.html

CZ SST “Perfect Pull” Trigger Adjustment

Tools required: 6mm wrench, 7mm wrench, one very small and one large common flathead screwdriver

“A” (standard trigger pull weight), “B” (creep), “C” (over-travel) and “D” (Set trigger pull weight).

•Make sure magazine and chamber are empty.
•Remove the stock from the barreled action.
•Cock the rifle then, adjust screw “B” in until it fires, back off ¼ turn.
•Loosen locking nut and remove screw “C” to allow easy access to screw “A”
•Adjust screw “A” to desired poundage and tighten the lock nut (ensuring that the screw position does not change).
•Replace screw “C”, turn it all the way in then back it out while pulling trigger until fires, then back out an additional ¼ turn, then tighten the lock nut for screw “C” down (ensuring that the screw position does not change).


Set Trigger Adjustment and Operation

To adjust the set trigger weight, adjust screw “D” in to lighten and out to make heavier. If you prefer to completely disable the set function, turn screw “D” all the way in until the rifle fires, then back off 1/4 turn.

An activated set-trigger is very sensitive to shock and during handling could unintentionally discharge if the set trigger is adjusted with too little travel. The safety of the SST adjustment can be checked with the rifle unloaded by repeated opening and closing of the bolt combined with moving of the safety to its “ON” and “OFF” positions in both set and unset modes. If the set trigger adjustment (engagement screw “D”) is too light, it will go off when doing this. In this case, add more travel to the set trigger adjustment until it does not simultaneously go off. (DISCLAIMER: Do not attempt trigger adjustments unless you are confident in your ability to follow instructions for adjustments and safe operation.)

For safety, activate the set-trigger only after the rifle is loaded and when in position for the shot with safety in the off position. Do not carry your rifle with an activated set-trigger! If you have activated the set-trigger and you do not immediately take the shot, keep your firearm pointed in a safe direction and with the safety on, squeeze the trigger.

This process will get you very close to the best trigger pull possible with only slight adjustments needed, if any, to get it to the “Perfect Pull” for you.


Resumen:
El tornillo D (el del peso del pelo) lo suyo es ajustarlo el ultimo, después de haber ajustado los otros tres.
El sistema es el habitual. Primero ajustas el desenganche, luego el peso y luego el sobrerecorrido.
recuerda que pueden interactuar entre ellos asi que después de cada nuevo ajuste tienes que probar que lo anterior sigue a tu gusto.
Haces las comprobaciones de seguridad habituales (acerrojado normal, acerrojado a lo bestia, lo de golpear la cantonera contra el suelo, y las comprobaciones de que el seguro funciona adecuadamente y no se modifican los ajustes por activarlo y desactivarlo) y cuando lo principal ya este a tu gusto te pones con el ajuste del pelo.

PD- Y Y una vez ya tengas todo finalizado puedes pesarlo con el sistema de la botella de agua para saber el peso exacto.

Re: Como tensar el gatillo del CZ 550

Publicado: 05 Sep 2013 21:19
por JAMPANA
Gracias , eres una mauina , ya te contare como quedo y gracias de nuevo